Which offcuts are worth keeping?
A piece is worth a label and a place on the rack only if it is long enough to be used again. Your policy sets a keep length, and when a piece is registered RemnantRack compares its guaranteed length, the measured length less the measurement uncertainty, with that keep length before anything is recorded.
A shorter piece goes to a supervisor's disposal review instead of filling the racks, and a damaged piece or one of unknown condition is quarantined. Approved rules can set different keep lengths and racks for different materials. Setting the keep length has its own page, Which offcuts are worth keeping?

How is each piece measured and labelled?
At the station, the operator scans the exact material code, measures one continuous usable length and enters it in millimetres or inches with the uncertainty of the measuring method, then records the piece's condition and any known batch. A shortened or unknown material code is refused, and RemnantRack never substitutes another material.
Registering creates the piece's own identity and a label with its barcode, material, length and rack. Each physical offcut is one record, even when several pieces have the same length. Labels print as 100 × 150 mm PDFs, downloaded or sent to your printer through SmartFACT PrintStation.

Where does it go?
A registered piece is not available yet. The operator attaches its label, scans the piece and then the card at its actual bin, which shows the materials and the longest piece that bin accepts, and confirms the put-away.
Only then does the piece appear in searches, in its recorded rack and bin. A label printed but never put away leaves the piece waiting, and reprinting a label does not create another piece.

What happens when it is pulled for a job?
To find a piece, enter the material, the finished length and how many blanks the job needs. RemnantRack adds the processing allowance, kerf, trim and any buffer, then lists the pieces long enough once measurement uncertainty is allowed for, with their rack and bin, and says why any piece was rejected.
Reserving a piece holds it for that job, so nobody else takes it. At the rack, the operator scans the reserved piece and its bin and checks it out before it is moved or cut, and from then on it is in use at that station.

What about the remainder after a cut?
After cutting, the operator records the blanks produced, the material lost to kerf and trim and the measured remainder. If those do not add up to the original piece within the measurement uncertainty, ordinary completion stops and the cut is held for a supervisor.
When the cut balances, the original piece is retired. A usable remainder gets a new identity and label, linked to the piece it came from, and goes through put-away like any other piece, so the two cannot both appear in a search.

What RemnantRack does not do
- Sheets, panels, grain direction or irregular shapes. Each piece is a straight length of one material and profile.
- Cutting optimisation or nesting. RemnantRack finds a suitable piece for the job in front of you; it does not plan a cutting list across your stock.
- Saw control. It sends nothing to a saw, and people measure, cut, label and dispose.
- Stock control: no purchasing, valuation or certified material traceability.
Common questions
Which materials does it handle?
Straight lengths of the materials you declare, such as aluminium profile, steel bar, tube or section, and plastic profile. Each material has an exact code with its profile, grade, finish and colour, so a different grade or finish is a different material, and one is never offered in place of another.
Can it replace an offcut spreadsheet?
Yes, for straight lengths. Existing offcuts can come in from a CSV import, but each one stays provisional until someone finds it, labels it, scans its bin and confirms the put-away. Start with one rack section and check it against the register before relying on it. After that, the register changes as pieces are reserved, cut and moved.
Is it a cutting optimiser?
No. RemnantRack finds and tracks individual offcuts for the job in front of you. It does not nest parts, optimise a cutting list across your stock or send instructions to a saw. If your cutting software already manages offcuts well, it may already do what you need.
Start free at one station and pay when you grow. While SmartFACT is in early access, we set your first workflow up with you.
